Metal Shear SD5-1

up to 1.0 mm steel

The SD5-1 is a very manoeuvrable shear and can make short turns (smallest inner radius 50 mm).
This is therefore the ideal shear for zinc processors, interior construction, body shops, garage companies and damage repair!

Metal Slitting Shears S1001N-1

up to 1.3 mm steel

Ideal shears for installation companies, assembly and craft.

Cutting air ducts, sandwich board, making a cold bridge and a thousands of other applications.

Metal Shear 1016-1

up to 1.6 mm steel

Universal powerful shear for sheet metal up to 1.6 mm and therefore particularly suitable for installation companies, assembly and craft. Ideal also in the reduction for cutting metal stud profiles.

Metal Slitting Shear 1020-1

up to 2.0 mm steel

This powerful shear is ideal for cutting U-, C-, O- and L-profiles and is particularly suitable for construction companies, air duct construction, switch cabinet construction etc., so wherever a higher capacity is desirable.

Universal Slitting Shear SD7-1

up to 2.0 mm steel 

The universal shear for straight lines and curves. Ideal for the automotive and commercial vehicle bodywork.

Useable like SD5-1, but with double capacity. Ideal for utility vehicles. Cutting steps and seams. Good curve ability (tightest radius 50 mm). 

Seam Metal Shear 3514-2

up to 2.0 mm, or 4x0.9 mm steel, or 6x0.75 mm light metal

Cold cutting without flying sparks!

This shear is ideal for cutting spiral ducts, roof seams, cross seams, ridge seams and folds of sheet iron, aluminum, lead, copper, zinc or stainless steel. Cuts roller shutter boxes, cover caps, grids and wire in cage- and aviary construction (flush-edged!).

Radius-Seam Metal Shear 3514-7R

up to 2.0 mm, or 4x0.75 mm steel

Cold cutting without flying sparks! Ideal for cutting recesses in spiral ducts and sheets of all kinds. Cuts straight and tight radii (min. 45 mm ø) in sheets and even over seams.

Ideal for air and climate technology, installation companies, truck workshops, metalworking companies etc.

Metal Stud & Stainless Steel Shear 3515

up to 2.3 mm steel

Due to the high performance, the low-vibration and soft cut ideal for separating UA stiffening profiles (up to 2 mm steel!) and for C & CW profiles in drywall construction. Saves the dangerous work with the angle grinder. No flying sparks, making it ideal for cutting indoors.

Profile Metal Shear 3520

up to 2.0 mm steel

The universal cutting device for the electrical installer, apparatus and control cabinet construction. The solution for cutting cable trays, cable tray lids, cable ladders, trapezoidal profile rungs, cable protection channels, stiffening UA profiles, wide span beams, cassettes, panels etc.
The profile shears effortlessly cuts across angles and profiles. 

Universal Shear UVS-1

up to 1.0 mm steel or 3.0 mm plastics

The Universal Shear UVS-1 is mostly used for interior-work, in buses, vans & trucks, to line or panel the roof, side or floor.

Tightest radius in plastic 30 mm and 50 mm metal to the left or right, depending on the thickness of the material.

Plastic Shears S1002N-1

especially for plastics, for example up to 3.0 mm PVC

Ideal for use in interior design, window dressing, acoustics, joineries, decor-, trade fair-, aircraft- and body construction and much more. 

Plastic Shear 3550

especially for plastics, for example up to 3.5 mm PVC

Ideal for use in interior design, window dressing, acoustics, joineries, decor-, trade fair-, aircraft- and body construction and much more.

Cable Pipe HDPE Slitter 3500

Cable tube shear for energy and telecom companies

Plastic shear 3500 is used for slitting plastic outer casings of fiber optic cables longitudinally for repair or other purposes. Also for cutting and slitting plastic cable covers and plastic tanks (up to 6mm HDPE).

Corrugated-electric Nibbler 1213-1

up to 1.3 mm steel

Crosswise and angle utting of corrugated, trapezoidal and square sheet profiles up to 85 mm profile heights.

Corrugated-electric Nibbler 1216-1

up to 1.6 mm steel

Flexible nibbler for sheet metals, trapezoidal sheet metals, corrugated sheet metals and profiles up to 85 mm profile heights.

Pneumatic Metal Shears 1910

up to 1.0 mm steel

Very manoeuvrable shear which makes short turns (smallest inner radius 50 mm).
This is the ideal shear for zinc processors, interior construction and garage companies!

Pneumatic Metal Shears 1913

up to 1.3 mm steel

Ideal shears for installation companies, assembly and craft and general purposes where pneumatic drive is desired.

Cutting air ducts, sandwich board, making a cold bridge and a thousands of other applications.

Pneumatic Metal Shears 1920

up to 2.0 mm steel

This powerful shear is ideal for cutting U-, C-, O- and L-profiles and is particularly suitable for construction companies, air duct construction, switch cabinets etc., so wherever a higher capacity is desirable and / or spark-free worked to become

Pneumatic Plastic Shear 1950

especially for plastics, for example up to 3.0 mm PVC

Ideal for use in interior design, decor construction, window dressing, exhibition construction, aircraft, body construction, acoustics, joineries and much more.

Splinter-free cutting of all plastic sheets.

Pneumatic Seam Metal Shears 19/3514-2

up to 2.0 mm steel

Ideal for cutting materials with thickened areas, seamed roofing membranes, spiral- and seam-folded tubes (even over the 4-fold seam), mesh, barrels, aluminum tear plate, sheet, stainless steel, Inox, aluminum, copper, zinc, U-shaped, C-,O- and L-profiles etc.

Pneumatic Radius Seam Metal Shears 19/3514-7R

up to 2.0 mm steel

Ideal for short turns (smallest inner radius 45 mm) and straight sections up to 2 mm plate material. Cuts pleats and thickenings.

Ideal shear for the recycling and the waste processing industry and wherever a high capacity is desirable and / or needs to be spark-free.

Pneumatic Metal Shears 19/3520

up to 2.0 mm steel

Profile shear with large blade opening, ideal for cutting over thickening of the material (for example ripples in cable ducts and overlaps) and for use in explosion hazardous areas.

Cordless Metal Shear AK 3010 Ni-MH

up to 1.0 mm sheet metal

Agile shear, handy for tight radii (50 mm) and therefore ideal for roof plumbers, interior fittings (for example, ceiling construction - installation of spots) and motor vehicle workshops (for example, when installing sun roofs).

5-piece 12 volt professional set AK 3010 Ni-MH consists of:
1 cordless shear AK 3010,
2 batteries MXL12,
1 charger RC and
1 transportbox.

Cordless Metal Shear AK 3013 Ni-MH

up to 1.3 mm sheet metal

This cordless shear is ideal for cutting and cut outs of sheet metal as well as U, C and L profiles. Cuts burr-free and without deformation. A universal sheet metal working device. Ideal shear for installation, air conditioning, ducting, aircraft manufacturing companies.

5-piece 12 volt professional set AK 3013 Ni-MH consists of:
1 cordless shear AK 3013 Ni-Mh,
2 batteries MXL12,
1 charger RC and
1 transportbox.

Cordless Metal Shear AK 3016 Ni-MH

up to 1.6 mm sheet metal

Ideal for cutting, cut-outs and trimming of all kind of sheets as well as U-,C- and L- profiles. Universal sheet processing device.

5-piece 12 volt professional set AK 3016 Ni-MH consists of:
1 cordless shear AK 3016 Ni-Mh,
2 batteries MXL12,
1 charger RC and
1 transportbox.

Cordless Radius Seam Metal Shear AK 3514-7R Ni-MH

Cordless Seam Metal Shear AK 3514-2 Ni-MH

up to 2.0 mm, or 4x0.9 mm steel, or 6x0.75 mm light metal

Cold cutting without flying sparks! Cutting of 6x-folded seams!!

This shear is ideal for cutting spiral ducts, roof seams, cross seams, ridge seams and folds of sheet iron, aluminum, lead, copper, zinc or stainless steel. Cuts roller shutter boxes, cover caps, grids and wire in cage- and aviary construction (flush-edged!).

5-piece 12 volt professional set AK 3514-2 Ni-MH consists of:
1 cordless shear AK 3514-2,
2 batteries MXL12,
1 charger RC and
1 transportbox.

Cordless Metal Shear AK 3520 Ni-MH

up to 2.0 mm steel

The profile metal shear AK 3520 is perfectly adapted to the needs of installation companies. It easily separates cable ducts, drywall profiles, but also spiral fold, flat sheets, U-, C- and L-profiles and much more.

5-piece 12 volt professional set AK 3520 Ni-MH consists of:
1 cordless shear AK 3520,
2 batteries MXL12,
1 charger RC and
1 transportbox.

Cordless Plastic Shear AK 3002 Ni-MH

especially for plastics, for example up to 3.0 mm PVC

Ideal for use in interior design, decor construction, window dressing, exhibition construction, aircraft, body construction, acoustics, joineries and much more.

5-piece 12 volt professional set AK 3002 Ni-MH consists of:
1 cordless shear AK 3002,
2 batteries MXL12,
1 charger RC and
1 transportbox.

Cordless metal shear 5-pcs.- professional AK 3010 Li-Ion

up to 1.0 mm steel

The AK 3010 Li-Ion is a very manoeuvrable shear and can make short turns (smallest inner radius 50 mm).
This is therefore the ideal shear for zinc processors, interior construction, body shops, garage companies and damage repair!

5-piece 18 volt professional set AK 3010 Li-Ion consists of:
1 cordless shear AK 3010 Li-Ion, 
2 batteries (2.0 Ah + 4.0 Ah),
1 charger CLi (30 Min.)
1 transport box.

Cordless metal shear 5-pcs.- professional AK 3013 Li-Ion

up to 1.3 mm metal

This cordless shear is ideal for cutting and cut outs of sheet metal as well as U, C and L profiles. Cuts burr-free and without deformation. A universal sheet metal working device. Ideal shear for installation, air conditioning, ducting, aircraft manufacturing companies.

5-piece 18 volt professional set AK 3013 Li-Ion consists of:
1 cordless shear AK 3013 Li-Ion, 
2 batteries (2.0 Ah + 4.0 Ah),
1 charger CLi (30 Min.),
1 transport box.

Cordless metal shear AK 3016 Li-Ion

Cordless Seam Metal Shear 5-pcs.-professional AK 3514-2 Li-Ion

up to 2.0 mm, or 4x0.9 mm steel, or 6x0.75 mm light metal

Cold cutting without flying sparks!

This shear is ideal for cutting spiral ducts, roof seams, cross seams, ridge seams and folds of sheet iron, aluminum, lead, copper, zinc or stainless steel. Cuts roller shutter boxes, cover caps, grids and wire in cage- and aviary construction (flush-edged!).

5-piece 18 volt professional set AK 3514-2 Li-Ion consists of:
1 cordless shear AK 3514-2 Li-Ion, 
2 batteries (2.0 Ah + 4.0 Ah),
1 charger CLi (30 Min.),
1 transport box.

Cordless Radius Seam Metal Shear AK 3514-7R Li-Ion

up to 2.0 mm, or 4x0.75 mm steel

Cold cutting without flying sparks! Ideal for cutting recesses in spiral ducts and sheets of all kinds. Cuts straight and tight radii (min. 45 mm ø) in sheets and even over seams.

Ideal for air and climate technology, installation companies, truck workshops, metalworking companies etc.

5-piece 18 volt professional set AK 3514-7R Li-Ion consists of:
1 cordless shear AK 3514-7R Li-Ion, 
2 batteries (2.0 Ah + 4.0 Ah),
1 charger CLi (30 Min.),
1 transport box.

Cordless Metal Stud Shear 5-pcs.-craftsman AK 3515 Li-Ion

up to 2.3 mm steel

Due to the high performance, the low-vibration and soft cut ideal for separating UA stiffening profiles (up to 2.0 mm steel!) and for C-, CW- and even UA-profiles in drywall construction. Saves the dangerous work with the angle grinder. No flying sparks, making it ideal for cutting indoors.

5-piece 18 volt professional set AK 3515 Li-Ion consists of:
1 cordless shear AK 3515 Li-Ion, 
2 batteries (2.0 Ah + 4.0 Ah),
1 charger CLi (30 Min.)
1 transport box.

Cordless Profile Metal Shear AK 3520 Li-Ion

up to 2.0 mm steel

The profile metal shear AK 3520 is perfectly adapted to the needs of installation companies. It easily separates cable ducts, drywall profiles, but also spiral fold, flat sheets, U-, C- and L-profiles and much more.

5-piece 18 volt professional set AK 3520 Li-Ion consists of:
1 cordless shear AK 3520 Li-Ion, 
2 batteries (2.0 Ah + 4.0 Ah),
1 charger CLi (30 Min.),
1 transport box.

Cordless pipe slitter plastic shear AK 3000 Li-Ion

Cable tube shear for energy and telecom companies up to 6.0 mm HDPE

Plastic shear AK3000 is used for slitting plastic outer casings of fiber optic cables longitudinally for repair or other purposes. Also for cutting and slitting plastic cable covers and plastic tanks (up to 6 mm HDPE) and ideal for waste disposal and low-residue emptying of tanks and barrels.

5-piece 18 volt professional set AK 3000 Li-Ion consists of:
1 cordless shear AK 3000 Li-Ion, 
2 batteries (2.0 Ah + 4.0 Ah),
1 charger CLi (30 Min.),
1 transport box.

Cordless Plastic Shear AK 3050 Li-Ion

especially for plastics, for example up to 3.0 mm PVC

Ideal for use in interior design, decor construction, window dressing, exhibition construction, aircraft, body construction, acoustics, joineries and much more. Splinter-free cutting of all plastic sheets.

5-piece 18 volt professional set AK 3050 Li-Ion consists of:
1 cordless shear AK 3050 Li-Ion, 
2 batteries (2.0 Ah + 4.0 Ah),
1 charger CLi (30 Min.),
1 transport box.